It is necessary to get used to any detector, will learn it to understand and the main thing not to hasten. Attentively listen that tells the detector, and then at the screen look. The main thing in a sound from the purpose. From a coin a sound accurate, sharp, from a rusty nail faltering and indistinct. The display is your assistant, in the beginning find out the purpose on a sound, find an accurate signal, and now it is possible to look at the display. All is simple. The index of the purpose (3) below - the purpose small, is less than copeck, perekrestie in the top - bolshej Olympic rouble or it is more than index. The more to the right perekrestie the index from the screen centre, the the rating of the purpose is more. The centre 0, and it is maximum to the right 32. At the copper purpose a rating 26-28. The Golden Ring 8-12 (depending on a ring).
Depth to the purpose is underlined in a kind stolbchatoj diagrammes (1), the more a column, the aim to a surface more close. With experience, you learn to define depth and the size of the purpose on a sound, Explorer has the big scale of the soundings, the different purposes sound differently.
Do not hasten, learn to understand the detector
I will give an example. On days off left with a companion to the place of old village with Explorer. Result 2 hour searches at a companion of 5 purposes at me more than 100, zamete, and worked on one site and absolutely identical detectors which have been adjusted on the standard program "Coins", without voice-frequency (threshold) tone (4). Having heard, that you had time to read above, and will read more low, at it tritely considerably it is better. The main thing! Does not hurry up and listen, listen. In the beginning try will learn to work with discriminator Coins adjustment if range strongly mineralizovan sensitivity (7) on "automatic machine" if the soil sensitivity on 32 ("automatic machine" allows to switch off). A voice-frequency sound establish on 6 so it quietly and studies, does not disturb, further necessarily voice-frequency sound do heard. The program of discrimination Coins. Beginning study, before installation of these values, for fidelity (I do not know, what options was are brought by you earlier) reboot the detector (at inclusion take red button Power while the detector will not reboot). For study choose a site not so littered and with soft soil.
How to conduct the search coil
It not a broom. Conduct the coil as it is possible more close to the earth, be not afraid, it is protected by a sheeting. Moving the coil here and there, watch, that in the end of movement it did not soar up upwards over the earth. Each your pass (one wave) should, necessarily, is blocked by following pass on a quarter of width of the coil. So you will avoid the admission of the purposes.
With the big or not deep purposes all is clear, an accurate, loud signal. But with the small and deep purposes it is more difficult.
During coil movement the small, uncertain signal has followed, like there would be a splash, time two and is not present it. Do not confuse with single loud signal splash, this static electricity. Stop, properly, check up a splash site, come from the different parties. The width of a wave of the coil should be 40-50 the Amplitude 0,7-1,5 seconds - 1 wave see. The signal can be weak and changeable. Here also it is useful to you voice-frequency (threshold) tone. Include it on 7 (should be heard). In a place where the purpose, the voice-frequency sound will vanish. Dig.
Tactics at definition of an exact site of the purpose. A mode “Pinpoint”.
Explorer it is equipped by rather useful option, allowing to define an exact site of the purpose “Pinpoint”. Adjustment is rather functional, simple in use. However, it be required to you some positive operational experience in a mode of this adjustment. We hope that our recommendations will promote its accumulation. So: having pressed key Pinpoint on the forward panel of the device, do not hasten, conduct the coil over the purpose as it is possible more slowly. Explorer will give a sound signal when the purpose will be directly under the coil centre.
It is necessary to notice that in mode Pinpoint, the detector is automatically switched from a discrimination mode in a mode of search of all metals. For example, at you the discrimination mask “Coint” is included and you have found out a copper coin. Having switched in mode Pinpoint, you can already hear two signals: the first from a coin, the second - from the iron nail which has appeared to numbers with a coin. In this case tactics can a life such: Disconnect mode Pinpoint. Stop and move the coil here and there. (Rice) see. Each pass of the coil should block the previous partially. Having surveyed, thus, some area in which there is a centre of a site of the purpose, try to plan a line on which the signal is audible most accurately and loudly. Then be developed on 90 degrees and repeat procedure. At you it will turn out two imaginary lines crossed at an angle of 90 degrees. Their crossing also will be the probable centre an object site.
It is necessary to tell, this way approaches for all metallodetektorov not equipped with function Pinpoint.
Pay attention! If the device submits a series of signals or on character of a signal you cannot unequivocally define an exact site – most likely the purpose very big or settles down close to a surface. In this case it is recommended to raise the coil over the earth and thus to make all manipulations.
Good luck and the main thing, do not hurry up.
I hope, our councils will help you to master Explorer.
|
